文档名:前处理对烧结多孔钛板镀铂包覆效果影响的研究
摘要:针对烧结多孔钛板镀铂工艺的提高,为解决前处理过程中表面除油不彻底、酸洗刻蚀不理想的问题,采用无水乙醇除油与50wt.%的硫酸作为酸洗刻蚀剂前处理的方法.研究了烧结多孔钛板镀铂工艺中不同的除油剂与刻蚀剂对铂镀层自身致密度及与钛基材结合度的影响.结果表明:在使用无水乙醇除油剂和沸腾状态下50wt.%硫酸刻蚀相结合的条件下,铂镀层紧致且与钛基材结合度较高.采用无水乙醇除油与硫酸刻蚀的方法可以提高镀层的致密度与结合度.
Abstract:Inordertoimprovetheplatinizationprocessofsinteredporoustitaniumplateandsolvetheproblemsofincompletesurfaceoilremovalandunsatisfactorypicklingetchingduringthepretreatmentprocess,anhydrousethanoloilremovaland50wt.%sulfuricacidwereusedasthefrontofpicklingetchingagent.Theeffectsofdifferentoilremoverandetcherontheself-densityofplatinumcoatingandthebindingdegreeoftitaniumsubstrateinsinteredporoustitaniumplateplatinizationwerestudied.Theresultsshowthattheplatinumcoatingiscompactandhasahighbindingdegreewithtitaniumsubstrateundertheconditionsofanhydrousethanoldegreasingagentcombinedwith50wt.%sulfuricacidetchingatboilingstate.Thedensityandbondingdegreeofthecoatingcanbeimprovedbythemethodofoilremovalbyanhydrousethanolandetchingbysulfuricacid.
作者:乔东伟 李朋喜 白佳凯 李黎明 丁睿 冯东辉Author:QiaoDongwei LiPengxi BaiJiakai LiLiming DingRui FengDonghui
作者单位:中国船舶集团有限公司第七一八研究所/中船(邯郸)派瑞氢能科技有限公司,河北邯郸056000
刊名:电镀与精饰
Journal:Plating&Finishing
年,卷(期):2024, 46(2)
分类号:TQ153.2
关键词:烧结多孔钛板 前处理 无水乙醇 硫酸 结合度
Keywords:sinteredporoustitaniumplate pretreatment anhydrousethanol sulfuricacid bindingdegree
机标分类号:R735.7TQ342+.31TG174.4
在线出版日期:2024年3月1日
基金项目:河北省科技厅项目前处理对烧结多孔钛板镀铂包覆效果影响的研究[
期刊论文] 电镀与精饰--2024, 46(2)乔东伟 李朋喜 白佳凯 李黎明 丁睿 冯东辉针对烧结多孔钛板镀铂工艺的提高,为解决前处理过程中表面除油不彻底、酸洗刻蚀不理想的问题,采用无水乙醇除油与50wt.%的硫酸作为酸洗刻蚀剂前处理的方法.研究了烧结多孔钛板镀铂工艺中不同的除油剂与刻蚀剂对铂镀层自...参考文献和引证文献
参考文献
引证文献
本文读者也读过
相似文献
相关博文
前处理对烧结多孔钛板镀铂包覆效果影响的研究 Study on the effect of pretreatment for platinum plating coating on sintered porous titanium plate
前处理对烧结多孔钛板镀铂包覆效果影响的研究.pdf
- 文件大小:
- 1.09 MB
- 下载次数:
- 60
-
高速下载
|
|